Products
Clean Steam Products Back to all Clean Steam Products
- In this category:
- FDA300
- FDA400
- FDA500
- FDA600
- FDA800
- Test Run
- PV926A
- PV926H
- PV928
- P130
- P130A
- P130C
- P130G
- P130H
- P130L
- P160 (2 1/2" - 3")
- P160
- P160A
- P173
- BKR2
- BKRI2
- BKV2
- BKVI2
- SRV6
- SRV8
- ISC16-ISC16I
- ISC201
- ISH10I
- Hygienic Balls Valves
- Check Valve
- Sample Cooler
- Sight Glass
- Clean Steam Separators
- Vacuum Breaker
- High Purity Ball Valves
Thermostatic Steam Trap
FDA300
Specifications
| Model | FDA 300 |
| Sizes | 1½” |
| Connections | Tri-Clamp |
| Body Material | Stainless Steel |
| Internal Surface Finish | 20-25 RA Finish |
| PMO Max. Operating Pressure | 90 PSIG |
| TMO Max. Operating Temperature | Saturated Steam Temperature |
| PMA Max. Allowable Pressure | 145 PSIG @ 338°F |
| TMA Max. Allowable Temperature | 350°F @ 132 PSIG |
| Internal RA Finish | 20-25 microinches |
| External RA Finish | 25-32 microinches |
| Notes | Electropolish to 15 Ra or lower is available |
Contact Us for more information on this product and to see other sizes that fit unique applications.
Typical Applications
PROCESS: FDA300 Series high-capacity thermostatic clean steam traps are used on clean steam applications, and for condensate drainage on CIP/SIP systems and various process vessels.
How It Works
This trap contains a welded 316L stainless steel thermal element that expands when heated and contracts when cooled. When air and subcooled condensate are present, the trap is in an open discharge position. When steam reaches the trap, the element expands, closing the trap tightly.
Thermostatic Steam Trap
FDA400
Specifications
| Model | FDA 401, FDA 402, FDA 403 |
| Sizes | ½”, ¾” |
| Connections | Tri-Clamp |
| Body Material | Stainless Steel |
| Internal Surface Finish | 20-25 RA Finish |
| PMO Max. Operating Pressure | 90 PSIG |
| TMO Max. Operating Temperature | Saturated Steam Temperature |
| PMA Max. Allowable Pressure | 145 PSIG @ 338°F |
| TMA Max. Allowable Temperature | 350°F @ 132 PSIG |
| Internal RA Finish | 20-25 microinches |
| External RA Finish | 25-32 microinches |
| Notes | 1. Special bellows available that sub-cools 2F°;
2. Electropolish to 15 Ra or lower is available |
Contact Us for more information on this product and to see other sizes that fit unique applications.
Typical Applications
DRIP, PROCESS: FDA400 Series thermostatic clean steam traps are used in clean steam applications such as drainage for CIP/SIP systems and various process vessels. The Universal horizontal connection allows the trap body to swivel to any angle. The FDA400 Series allows for a 90-degree connection on either the inlet or outlet capable of 360-degree orientation.
How It Works
This trap contains a welded 316L stainless steel thermal element that expands when heated and contracts when cooled. When air and subcooled condensate are present, the trap is in an open discharge position. When steam reaches the trap, the element expands, closing the trap tightly
Thermostatic Steam Trap
FDA500
Specifications
| Model | FDA 500, FDA 510 |
| Sizes | ½”, ¾”, 1”, 1½” |
| Connections | Tri-Clamp, NPT, Tube Weld |
| Body Material | Stainless Steel |
| Internal Surface Finish | 20-25 RA Finish |
| PMO Max. Operating Pressure | 90 PSIG |
| TMO Max. Operating Temperature | Saturated Steam Temperature |
| PMA Max. Allowable Pressure | 145 PSIG @ 338°F |
| TMA Max. Allowable Temperature | 350°F @ 132 PSIG |
| Internal RA Finish | 20-25 microinches |
| External RA Finish | 25-32 microinches |
| Notes | 1. Special bellows available that sub-cools 2°F 2. Electropolish to 15 Ra or lower is available |
Contact Us for more information on this product and to see other sizes that fit unique applications.
Typical Applications
DRIP, PROCESS: FDA500 Series thermostatic clean steam traps are used in clean steam applications as drip traps on piping runs as well as for drainage for CIP/SIP systems and various process vessels.
How It Works
This trap contains a welded 316L stainless steel thermal element that expands when heated and contracts when cooled. When air and subcooled condensate are present, the trap is in an open discharge position. When steam reaches the trap, the element expands, closing the trap tightly
Thermostatic Steam Trap
FDA600
Specifications
| Model | FDA 600 |
| Sizes | ½”, ¾”, 1” |
| Connections | Tri-Clamp, NPT, Tube Weld |
| Body Material | Stainless Steel |
| PMO Max. Operating Pressure | 110 PSIG |
| TMO Max. Operating Temperature | Saturated Steam Temperature |
| PMA Max. Allowable Pressure | 145 PSIG @ 338°F |
| TMA Max. Allowable Temperature | 350°F @ 132 PSIG |
| Internal RA Finish | CF |
| External RA Finish | CF |
Contact Us for more information on this product and to see other sizes that fit unique applications.
Typical Applications
DRIP, PROCESS: FDA600 Series thermostatic clean steam traps are used as drip traps on piping runs on clean steam applications and for drainage for CIP/SIP systems and various process vessels.
How It Works
This trap contains a welded 316L stainless steel thermal element that expands when heated and contracts when cooled. When air and subcooled condensate are present, the trap is in an open discharge position. When steam reaches the trap, the element expands, closing the trap tightly
Thermodynamic Steam Trap
FDA800
Specifications
| Model | FDA 800 |
| Sizes | ½” |
| Connections | Tri-Clamp, NPT, Tube Weld |
| Body Material | Stainless Steel |
| Internal Surface Finish | CF |
| PMO Max. Operating Pressure | 150 PSIG |
| TMO Max. Operating Temperature | 500°F |
| PMA Max. Allowable Pressure | 230 PSIG @ 850°F |
| TMA Max. Allowable Temperature | 850°F @ 230 PSIG |
| Internal RA Finish | CF |
| External RA Finish | CF |
Contact Us for more information on this product and to see other sizes that fit unique applications.
Typical Applications
DRIP: The FDA800 Series thermodynamic clean steam traps are used as drip traps on steam mains in CIP/SIP systems and drainage for separators and filters
How It Works
Using the thermodynamic properties of flash steam, this trap features a disc that is pushed open by incoming condensate, then closes tightly when steam enters the trap. Because it normally operates in an open position, condensate is continuously discharged from the line. Steam entering the trap creates an internal pressure that forces the valve to close tightly, preventing the steam from escaping.
Test run
Test Run
Specifications
hello
Contact Us for more information on this product and to see other sizes that fit unique applications.
Typical Applications
hey
How It Works
hi
Pneumatic Control Valve
PV926A
Specifications
| Model | PV926A |
| Service | Saturated Steam, hot and superheated water
Process fluids, liquids, air and gases compatible with the construction |
| Sizes | ½” to 2” |
| Connections | ¼” NPT-F |
| Body Material | Stainless Steel |
| Body Design Conditions | PN16 |
| Max Operating Pressure | 188.5 PSIG at 100.4°F |
| Maximum Operating Steam Pressure | 87 PSIG |
| Max Operating Temp. (Steam & Water) | 338°F |
| Max Operating Temp. (Air) | 302°F |
| Min. Operating Temperature | 14°F |
| Max. Air Supply Pressure | 43.5, 72.52 PSIG |
| Max. Ambient Temperature | 158°F |
| Min. Ambient Temperature | -4°F |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
| External RA Finish | 0.76 micron; 29.9213 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
The PV926A aseptic control valves are single seated, two-way body constructed with angle connections. The PA pneumatic actuator features a rubber diaphragm and multi-springs. Its action can be DA – direct action (air to close) or RA – reverse action (air to open). The PV926A valves have been designed to ensure an accurate control in any process condition. The self-draining design is ideally suited for clean steam service applications.
Pneumatic Control Valve
PV926H
Specifications
| Model | PV926H |
| Service | Saturated Steam, hot and superheated water
Process fluids, liquids, air and gases compatible with the construction |
| Sizes | ½” to 4” |
| Connections | ¼” NPT-F |
| Body Material | Stainless Steel |
| Body Design Conditions | PN16 |
| Max Operating Pressure | 188.5 PSIG at 100.4°F |
| Maximum Operating Steam Pressure | 87 PSIG |
| Max Operating Temp. (Steam & Water) | 338°F |
| Max Operating Temp. (Air) | 302°F |
| Min. Operating Temperature | 14°F |
| Max. Air Supply Pressure | 43.5, 72.5 PSIG |
| Max. Ambient Temperature | 158°F |
| Min. Ambient Temperature | -4°F |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
| External RA Finish | 0.76 micron; 29.9213 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
The PV926H hygienic control valves are single seated, two-way body constructed with angle connections. The PA pneumatic actuator features a rubber diaphragm and multi-springs. Its action can be DA – direct action (air to close) or RA – reverse action (air to open). The PV926H valves have been designed to ensure an accurate control in any process condition. Their self-draining design is ideally suited for clean steam service applications.
Pneumatic Control Valve
PV928
Specifications
| Model | PV928L, PV928H, PV928M, PV928D |
| Service | Saturated Steam, hot and superheated water
Process fluids, liquids, air and gases compatible with the construction |
| Sizes | ½” to 4” |
| Connections | ¼” NPT-F |
| Body Material | Stainless Steel |
| Body Design Conditions | PN16 |
| Max Operating Pressure | 188.5 PSIG at 100.4°F |
| Maximum Operating Steam Pressure | 87 PSIG |
| Max Operating Temp. (Steam & Water) | 338°F |
| Max Operating Temp. (Air) | 302°F |
| Min. Operating Temperature | 14°F |
| Max. Air Supply Pressure | 43.5, 72.52 PSIG |
| Max. Ambient Temperature | 158°F |
| Min. Ambient Temperature | -4°F |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
| External RA Finish | 0.76 micron; 29.9213 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
The PV928 are two- or three-way control valves with angle connections, specially designed for food, chemical, pharmaceutical and cosmetic industries among others. The PA pneumatic actuator features a rubber diaphragm and multi-springs. Its action can be DA – direct action (air to close) or RA-reverse action (air to open). The PV928 valves have been designed to ensure an accurate control in any process condition and they have self-draining design.
Sanitary Pressure Reducing Valve
P130
Specifications
| Model | P130 |
| Service | Clean air, nitrogen, carbon dioxide, oxygen, argon, and other gases or liquids compatible with the construction |
| Sizes | ½” to 1”; DN08 to DN25 (1/4” to 1”) |
| Connections | Clamp ferrules or others on request |
| Body Material | 316L Stainless Steel |
| Max. Upstream Pressure | 232.1 PSIG |
| Max. Downstream Pressure | 116 PSIG |
| Min. Down Steam Pressure | 0, 29 PSIG |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
| External RA Finish | 0.76 micron; 29.9213 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
The ADCA P130 series direct acting, spring-loaded diaphragm sensing, pressure reducing valves are designed for use with clean air, nitrogen, carbon dioxide, oxygen, argon and other gases or liquids compatible with the construction materials and valve design. This valve is specifically designed for the high purity gas systems found in the pharmaceutical, cosmetic, fine chemical and food & beverage processes.
Sanitary Pressure Reducing Valve
P130A
Specifications
| Model | P130A |
| Service | Clean air, nitrogen, carbo dioxide, oxygen, argon, and other gases or liquids compatible with the construction |
| Sizes | ½” to 1”; DN08 to DN25 (1/4” to 1”) |
| Connections | Clamp ferrules or others on request |
| Body Material | 316L Stainless Steel |
| Max. Upstream Pressure | 232.1 PSIG |
| Max. Downstream Pressure | 116 PSIG |
| Min. Down Steam Pressure | 0, 29 PSIG |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
| External RA Finish | 0.76 micron; 29.9213 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
The ADCA P130A series direct acting, dome loaded, diaphragm sensing pressure reducing valves are designed for use with clean air, nitrogen, carbon dioxide, oxygen, argon and other gases or liquids compatible with the construction materials and valve design.
Sanitary Pressure Reducing Valve
P130C
Specifications
| Model | P130C |
| Service | Clean air, nitrogen, carbo dioxide, oxygen, argon, and other gases or liquids compatible with the construction |
| Sizes | ½” to 1”; DN08 to DN25 (1/4” to 1”) |
| Connections | Clamp ferrules or others on request |
| Body Material | 316L Stainless Steel |
| Max. Upstream Pressure | 232.1 PSIG |
| Max. Downstream Pressure | 116 PSIG |
| Min. Down Steam Pressure | 0, 29 PSIG |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
| External RA Finish | 0.76 micron; 29.9213 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
The ADCA P130C series direct acting, spring-loaded diaphragm sensing, pressure reducing valves are designed for use with clean air, nitrogen, carbon dioxide, oxygen, argon and other gases or liquids compatible with the construction materials and valve design. This valve is specifically designed for the high purity gas systems found in the pharmaceutical, cosmetic, fine chemical and food & beverage processes.
Sanitary Pressure Reducing Valve
P130G
Specifications
| Model | P130G |
| Service | Clean air, nitrogen, carbo dioxide, oxygen, argon, and other gases or liquids compatible with the construction |
| Sizes | 1½”; DN 32 and DN 40 (1¼” and 1½”) |
| Connections | Clamp ferrules or others on request |
| Body Material | 316L Stainless Steel |
| Max. Upstream Pressure | 232.1 PSIG |
| Max. Downstream Pressure | 116 PSIG |
| Min. Down Steam Pressure | 0, 29 PSIG |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
| External RA Finish | 0.76 micron; 29.9213 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
The ADCA P130G series direct acting, spring-loaded diaphragm sensing, balanced plug, pressure reducing valves are designed for use with clean air, nitrogen, carbon dioxide, oxygen, argon and other gases or liquids compatible with the construction materials and valve design. This valve is specifically designed for the high purity gas systems found in the pharmaceutical, cosmetic, fine chemical and food & beverage processes.
Sanitary Pressure Reducing Valve
P130H
Specifications
| Model | P130H |
| Service | Clean air, nitrogen, carbo dioxide, oxygen, argon, and other gases or liquids compatible with the construction |
| Sizes | 1”; DN 25 (1”) |
| Connections | Clamp ferrules or others on request |
| Body Material | 316L Stainless Steel |
| Max. Upstream Pressure | 232.1 PSIG |
| Max. Downstream Pressure | 116 PSIG |
| Min. Down Steam Pressure | 0, 29 PSIG |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
| External RA Finish | 0.76 micron; 29.9213 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
The ADCA P130H series direct acting, spring-loaded diaphragm sensing, balanced plug, pressure reducing valves are designed for use with clean air, nitrogen, carbon dioxide, oxygen, argon and other gases or liquids compatible with the construction materials and valve design. This valve is specifically designed for the high purity gas systems found in the pharmaceutical, cosmetic, fine chemical and food & beverage processes.
Sanitary Pressure Reducing Valve
P130L
Specifications
| Model | P130L |
| Service | Clean air, nitrogen, carbo dioxide, oxygen, argon, and other gases or liquids compatible with the construction |
| Sizes | ½” to ¾”; DN 08 to DN 20 (1/4” to 1”) |
| Connections | Clamp ferrules or others on request |
| Body Material | 316L Stainless Steel |
| Max. Upstream Pressure | 232.1 PSIG |
| Max. Downstream Pressure | 116 PSIG |
| Min. Down Steam Pressure | 0, 29 PSIG |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
| External RA Finish | 0.76 micron; 29.9213 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
The ADCA P130L low flow series direct acting, spring-loaded diaphragm sensing, pressure reducing valves are designed for use with clean air, nitrogen, carbon dioxide, oxygen, argon and other gases or liquids compatible with the construction materials and valve design. This valve is specifically designed for the high purity gas systems found in the pharmaceutical, cosmetic, fine chemical and food & beverage processes.
Sanitary Pressure Reducing Valve
P160 (2 1/2" - 3")
Specifications
| Model | P160 |
| Service | Clean Steam, compressed air, water, and other gases and liquids compatible with the construction |
| Sizes | 2 ½” and 3” |
| Connections | ASME BPE
Clamp ferrules or others on request |
| Body Material | BSM |
| Max. Upstream Pressure | 116 PSIG |
| Max. Downstream Pressure | 58 PSIG |
| Min. Down Steam Pressure | 14.5 PSIG |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
| External RA Finish | 0.76 micron; 29.9213 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
The ADCA P160 series direct acting, spring-loaded, diaphragm sensing pressure reducing valves are designed for use with clean steam, compressed air, water and other gases or liquids compatible with the construction materials.
Sanitary Pressure Reducing Valve
P160
Specifications
| Model | P160 |
| Service | Clean Steam, compressed air, water, and other gases and liquids compatible with the construction |
| Sizes | ¾” to 2”; DN 20 to 50 (3/4” to 2”) |
| Connections | Clamp ferrules or others on request |
| Body Material | BSM |
| Max. Upstream Pressure | 116 PSIG
58 PSIG * |
| Max. Downstream Pressure | 72.5 PSIG |
| Min. Down Steam Pressure | 0, 116 PSIG |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
| External RA Finish | 0.76 micron; 29.9213 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
The ADCA P160 series direct acting, spring-loaded, diaphragm sensing pressure reducing valves are designed for use with clean steam, compressed air, water and other gases or liquids compatible with the construction materials.
Sanitary Pressure Reducing Valve
P160A
Specifications
| Model | P160A |
| Service | Clean Steam, compressed air, water, and other gases and liquids compatible with the construction |
| Sizes | ¾” to 2”; DN 20 to DN 50 (3/4” to 2”) |
| Connections | Clamp ferrules or others on request |
| Body Material | BSM |
| Max. Upstream Pressure | 116 PSIG |
| Max. Downstream Pressure | 87 PSIG |
| Min. Down Steam Pressure | 0, 116 PSIG |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
| External RA Finish | 0.76 micron; 29.9213 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
The ADCA P160A series direct acting, dome loaded, diaphragm sensing pressure reducing valves are designed for use with clean steam, compressed air, water and other gases or liquids compatible with the construction materials.
Sanitary Pressure Reducing Valve
P173
Specifications
| Model | P173 |
| Service | Clean Steam, compressed air, water, and other gases and liquids compatible with the construction |
| Sizes | 1½”, 2”; DN 32 to DN 50 (1 ¼” to 2”) |
| Connections | Clamp ferrules or others on request |
| Body Material | BSM |
| Max. Upstream Pressure | 116 PSIG
58 PSIG * |
| Max. Downstream Pressure | 72.5 PSIG |
| Min. Down Steam Pressure | 0, 116 PSIG |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
| External RA Finish | 0.76 micron; 29.9213 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
The ADCA P173 series direct acting, spring-loaded diaphragm sensing, pressure reducing valves are designed for use with clean steam, compressed air, water and other gases or liquids compatible with the construction materials.
Sanitary Tank Blanketing Regulator
BKR2
Specifications
| Model | BKR2 – Low pressure regulator |
| Service | Compressed air, nitrogen and other gases compatible with the construction |
| Sizes | 1” – DN 25 |
| Connections | Clamp end or others on request |
| Body Material | AISI 316L (Stainless Steel) |
| Max. Upstream Pressure | Seat Ø 5 mm 174 PSIG
Seat Ø 8 mm 87 PSIG |
| Max. Downstream Pressure | 7.25 PSI |
| Min. Down Steam Pressure | .07 PSI |
| Max. Design Temperature | 266°F |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
| External RA Finish | 0.76 micron; 29.9213 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
Tank blanketing valves are commonly used in tank storage systems to prevent and protect against explosions (avoiding flammable liquids being vented from vessel), to control product contamination against external air that may fill the vapor space, to reduce evaporation losses (consequently, production losses), to reduce internal corrosion (caused by air and moisture) and to prevent vacuum condition. The blanketing process consists in covering the stored medium, usually a liquid, with a gas (normally N2).
Sanitary Tank Blanketing Regulator
BKRI2
Specifications
| Model | BKRI2 – Low pressure regulator |
| Service | Compressed air, nitrogen and other gases compatible with the construction |
| Sizes | DN 15 and DN 25 (1/2” and 1”) |
| Connections | Flanged EN 1092-1 PN16 |
| Body Material | CF3M (Stainless Steel) |
| Max. Upstream Pressure | Seat Ø 5 mm 174 PSIG
Seat Ø 8 mm 87 PSIG |
| Max. Downstream Pressure | 7.25 PSI |
| Min. Down Steam Pressure | .07 PSI |
| Max. Design Temperature | 266°F |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
Tank blanketing valves are commonly used in tank storage systems to prevent and protect against explosions (avoiding flammable liquids being vented from vessel), to control product contamination against external air that may fill the vapor space, to reduce evaporation losses (consequently, production losses), to reduce internal corrosion (caused by air and moisture) and to prevent vacuum condition. The blanketing process consists in covering the stored medium, usually a liquid, with a gas (normally N2).
Sanitary Tank Blanketing Regulator
BKV2
Specifications
| Model | BKV2– Low pressure venting valve |
| Service | Compressed air, nitrogen and other gases compatible with the construction |
| Sizes | 1” – DN 25 |
| Connections | Clamp ends or others on request |
| Body Material | AISI 316L (Stainless Steel)
Hastelloy C22 |
| Max. Operating Pressure | 87 PSIG |
| Min. Upstream Pressure | .07 PSI |
| Max. Upstream Pressure | 7.25 PSI |
| Max. Design Temperature | 266°F |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
| External RA Finish | 0.76 micron; 29.9213 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
Tank blanketing valves are commonly used in tank storage systems to prevent and protect against explosions (avoiding flammable liquids being vented from vessel), to control product contamination against external air that may fill the vapor space, to reduce evaporation losses (consequently, production losses), to reduce internal corrosion (caused by air and moisture) and to prevent vacuum condition. The blanketing process consists in covering the stored medium, usually a liquid, with a gas (normally N2).
Sanitary Tank Blanketing Regulator
BKVI2
Specifications
| Model | BKVI– Low pressure venting valve |
| Service | Compressed air, nitrogen and other gases compatible with the construction |
| Sizes | DN 15 – DN 25 (1/2” – 1”) |
| Connections | Flanged EN 1092-1 (Steel) PN16 |
| Body Material | CF3M |
| Max. Operating Pressure | 87 PSIG |
| Min. Upstream Pressure | .07 PSI |
| Max. Upstream Pressure | 7.25 PSI |
| Max. Design Temperature | 266°F |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
Tank blanketing valves are commonly used in tank storage systems to prevent and protect against explosions (avoiding flammable liquids being vented from vessel), to control product contamination against external air that may fill the vapor space, to reduce evaporation losses (consequently, production losses), to reduce internal corrosion (caused by air and moisture) and to prevent vacuum condition. The blanketing process consists in covering the stored medium, usually a liquid, with a gas (normally N2).
Safety Relief Valve
SRV6
Specifications
| Model | SRV6 |
| Service | Clean steam, air, water, and other gases and liquids compatible with the construction |
| Sizes | ¾” x 1”, 1” x 1½”, 1½” x 2”, and 2” x 2”
DN 20×25 (3/4”x 1”), DN 25×40 (1”x 1½”), DN 32×40 (1¼” x 1½”) and DN 40×50 (1½” x 2”) |
| Connections | Clamp ends or others on request |
| Body Material | AISI 316L (Stainless Steel) |
| Max. Operating Pressure | 232 PSIG |
| Max. Operating Temperature | 356°F |
| Min. Operating Temperature | -40°F |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
| External RA Finish | 0.76 micron; 29.9213 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
The ADCA SRV6 series aseptic safety relief valves with angle type connections are designed for use with clean steam, air, water and other gases and liquids compatible with the construction materials. Main applications are overpressure protection on steam equipment, pressure vessels and pipelines, particularly within the food, beverage and pharmaceutical industries.
Safety Relief Valve
SRV8
Specifications
| Model | SRV8 |
| Service | Clean steam, air, water, and other gases and liquids compatible with the construction |
| Sizes | ¾” x 1”, 1” x 1½”, 1½” x 2”, and 2” x 2”
DN 20×25 (3/4”x 1”), DN 25×40 (1”x 1½”), DN 32×40 (1¼” x 1½”) and DN 40×50 (1½” x 2”) |
| Connections | Clamp ferrules or others on request |
| Body Material | AISI 316L (Stainless Steel) |
| Max. Operating Pressure | 232 PSIG |
| Max. Operating Temperature | 356°F |
| Min. Operating Temperature | -40°F |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
| External RA Finish | 0.76 micron; 29.9213 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
The ADCA SRV8 series aseptic safety relief valves with angle type connections are designed for use with clean steam, air, water and other gases and liquids compatible with the construction materials. Main applications are overpressure protection on steam equipment, pressure vessels and pipelines, particularly within the food, beverage and pharmaceutical industries.
Hygienic Steam Filter
ISC16-ISC16I
Specifications
| Model | ISC16, ISC16I |
| Service | Steam, compressed air, and other gases |
| Sizes | ¼” to 3”
DN 10 to DN 80 (3/8” to 3”) [DN 100 to DN 200 (4” to 8”) on request] |
| Connections | Female threaded ISO 7 Rp of NPT
Flanged EN 1092-1 PN16 Flanged ANSI B 16.5 Class 150 lb Welded ends and other connections on request |
| Body Material | AISI 304 (Stainless Steel) |
| Internal RA Finish | 0.76 micron; 29.9213 microinches |
| External RA Finish | 1.6 micron; 62.99 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
The ISC16 high efficiency filters are used to remove contaminated particles from gases such as steam and compressed air. The optimized construction of these units offers low differential pressure at high flow rates. All sizes are built in two halves. Up to 3” / DN 80 they are joined by a food industry fitting according to DIN 11851 and the larger sizes DN 100 to DN 200 by flat flanges fixed with bolts and nuts. The filter elements (replaceable) are made of sintered austenitic stainless steel.
Hygienic Steam Filter
ISC201
Specifications
| Model | ISC201 |
| Service | Steam, compressed air, and other gases |
| Sizes | ¼” to 2”
DN 10 to DN 80 (3/8” to 3”) |
| Connections | Female threaded ISO 7 Rp or NPT
Flanged EN 1092-1 PN16 Flanged ANSI B 16.5 Class 150 lb Welded ends and other connections on request |
| Body Material | AISI 316L |
| Internal RA Finish | 0.76 micron; 29.9213 microinches |
| External RA Finish | 1.6 micron; 62.99 microinches
|
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
The ISC20I high efficiency filters are used to remove contaminated particles from gases such as steam and compressed air. The optimized construction of these units offers low differential pressure at high flow rates. All sizes are built in two halves, joined by a sanitary clamp ferrule according to DIN 32676 Series A, with drain connection on bottom. The filter elements (replaceable) are made of sintered austenitic stainless steel.
Hygienic Steam Filter
ISH10I
Specifications
| Model | ISH10I |
| Service | Steam, compressed air, and other gases |
| Sizes | 1/2” to 2”
DN 10 to DN 50 (3/8” TO 2”) |
| Connections | Sanitary clamp ferrules
Welded ends, threaded, flanged DIN or ANSI on request |
| Body Material | AISI 316L |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
| External RA Finish | 0.76 micron; 29.9213 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
The ISH10I high efficiency filters are used to remove contaminated particles from gases such as steam and compressed air. The optimized construction of these units offers low differential pressure at high flow rates. All sizes are built in two halves and are joined by a sanitary clamp ferrule according to DIN 32676 Series A. The filter elements (replaceable) are made of sintered austenitic stainless steel.
Hygienic Balls Valves
Hygienic Balls Valves
Specifications
| Model | M3H True Bore (DN10-50 DIN), M3H True Bore (1/2”-2” ASME BPR) |
| Service | Clean Steam, gases, and liquids compatible with the construction |
| Sizes | DN 10 to DN 50, ½” – 2” ASME BPR |
| Connections | According to DIN 11850 tube, According to ASME BPE
TC – Sanitary clamps DIN 32676, TC-Sanitary clamps ETO – Extended tube orbital welding TC/ETO – Combination |
| Model | M3H Full Bore (6” ASME BPR) |
| Service | Clean Steam, gases, and liquids compatible with the construction |
| Sizes | 6” |
| Connections | According to ASME BPE
TC – Sanitary clamps ETO – Extended tube orbital welding TC/ETO – Combination |
| Model | M3H True Bore (2-1/2”-4 ASME BPR), M3H Full Bore (DN65-100 DIN) |
| Service | Clean Steam, gases, and liquids compatible with the construction |
| Sizes | 2½”-4”, DN 65 to DN 100 |
| Connections | According to ASME BPE, According to DIN 11850 tube
TC – Sanitary clamps, TC – Sanitary clamps DIN 32676 ETO – Extended tube orbital welding TC/ETO – Combination |
Contact Us for more information on this product and to see other sizes that fit unique applications.
Typical Applications
M3H three pieces body ball valves are isolating valves designed for use with clean steam, condensate and other gases and liquids used in high purity and aseptic processes. The valve is not designed as a control valve and should only be used as an isolating valve, fully open or fully closed. The product is mainly designed for the pharmaceutical, biotech, semiconductor, cosmetics, fine chemical, food and beverage industries.
Check Valve
Check Valve
Specifications
| Model | SRT10- Vertical Installation
SRTH10 – Horizontal Installation |
| Service | Clean Steam, water and other gases and liquids compatible with the construction |
| Sizes | ½” to 4” |
| Connections | Clamp ferrules or others on request |
| Body Material | Stainless Steel |
| Max. Operating Temperature (steam and water) – EPDM seals | 356°F |
| Max. Operating Temperature (air and other gases) – EPDM seals | 302°F |
| Max Operating Temperature -PTFE seals | 392°F |
| Minimum Operating Temperature | 14°F |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
| External RA Finish | 0.76 micron; 29.9213 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
The SRT10 all stainless-steel disc check valve has a compact design and is specially designed for use with clean steam, hot condensate and other process fluid applications. They are particularly recommended for high purity applications
Will be assembled and packaged in a clean room certified according to ISO 14644-1. These products are end capped and sealed with recyclable thermo-shrinkable plastic film, to avoid contamination.
Sample Cooler
Sample Cooler
Specifications
| Model | SC32P – permanent sampling
SC32PP – portable design |
| Service | Steam boilers
Hot water Systems |
| Sizes &
Connections |
Cooling water inlet/outlet: ½” on body (BSP or NPT) or ¾” tri-clamp
Sample tube inlet/outlet: 8mm O/D Alternative ½” tri-clamp compatible |
| Limiting Conditions
– Pressure
– Temperature |
Body
290psig (20 Bar)
248° F (120° C) |
| Limiting Conditions
– Pressure
– Temperature |
Coil
SC32P:1595 psig (110 Bar) SC32PP: 1305 psig (90 Bar)
SC32P: 752° F (400° C) SC32PP: 842° F (450° C) |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
| External RA Finish | 0.76 micron; 29.9213 microinches
|
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
ADCA sample coolers are specially designed to cool samples of boiler water or steam for analysis. Sample coolers prevent steam flashing-off from hot pressurized liquid samples, which can be dangerous and may result in an incorrect water sample. This device may be used for boiler water analysis and other sampling or cooling applications compatible with the construction materials.
Will be assembled and packaged in a clean room certified according to ISO 14644-1. These products are end capped and sealed with recyclable thermo-shrinkable plastic film, to avoid contamination.
Sight Glass
Sight Glass
Specifications
| Model | SWS |
| Service | Water and other gases and liquids compatible with the construction |
| Sizes | ½” to 4” |
| Connections | Clamp ferrules or others on request |
| Max. Operating Temperature (steam and water) – EPDM seals | 356°F |
| Max. Operating Temperature (air and other gases) – EPDM seals | 302°F |
| Max Operating Temperature -PTFE seals | 392°F |
| Minimum Operating Temperature | 14°F |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
| External RA Finish | 0.76 micron; 29.9213 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
The SWS sanitary sight glasses are designed to monitor liquid flow in any direction. Sight glasses (or flow indicators) are usually employed to detect either the presence or absence of fluid flow, turbulence, color, etc. They are specially recommended for high purity applications.
Will be assembled and packaged in a clean room certified according to ISO 14644-1. These products are end capped and sealed with recyclable thermo-shrinkable plastic film, to avoid contamination.
Clean Steam Separators
Clean Steam Separators
Specifications
| Model | S10H
S10HA- with air vent connection |
| Service | Steam, compressed air, and other gases |
| Sizes | ½” to 3” |
| Connections | Clamp ferrules ASME BPE
Other Sanitary clamp or tube weld connections available on request |
| Model | S10HV |
| Service | Steam, compressed air, and other gases |
| Sizes | ½”, ¾”, 1”, 1½”, and 2” |
| Connections | Clamp ferrules ASME BPE
Other Sanitary clamp or tube weld connections available on request |
| Model | S11
S11A- with air vent connection |
| Service | Steam, compressed air, and other gases |
| Sizes | ½”, ¾”, 1”, 1½”, and 2” |
| Connections | Clamp ferrules ASME BPE
Other Sanitary clamp or tube weld connections available on request |
Contact Us for more information on this product and to see other sizes that fit unique applications.
Typical Applications
When wet steam is used in sterilization, moisture in suspension reduces the heat transfer efficiency, and the validity of the sterilization process can be compromised. S10H series baffle separators remove moisture from steam pipelines. Steam passes through the separator and as a result of expansion, impact and swirling effects, the particles with a heavier specific gravity are separated, such as water droplets and moisture in suspension. The condensate collected at the bottom of the separator must be automatically drained by a suitable steam trap.
When wet steam is used in sterilization, moisture in suspension reduces the heat transfer efficiency, and the validity of the sterilization process can be compromised. S10HV series centrifugal separators remove moisture from steam pipelines. Steam passes through the separator and as a result of centrifugal forces, impact and swirling effects, the particles with a heavier specific gravity are separated, such as water droplets and moisture in suspension. The condensate collected at the bottom of the separator must be automatically drained by a suitable steam trap.
When wet steam is used in sterilization, moisture in suspension reduces the heat transfer efficiency, and the validity of the sterilization process can be compromised. S11 series centrifugal separators remove moisture from steam pipelines. Steam passes through the separator and, as a result of centrifugal forces, impact and swirling effects, the particles with a heavier specific gravity are separated, such as water droplets and moisture in suspension. The condensate collected at the bottom of the separator must be automatically drained by a suitable steam trap.
Vacuum Breaker
Vacuum Breaker
Specifications
| Model | VB16C |
| Service | Saturated steam and other gases compatible with the construction |
| Sizes | 1” – DN 25 |
| Connections | ASME BPE, DIN and ISO
Clamp ferrules or others on request |
| Max. Operating Pressure | 188.5 psig @ 100.4°F |
| Max. Operating Steam Pressure | 87 psig |
| Max Operating Temperature (steam and water) | 338°F |
| Minimum Operating Temperature | 14°F |
| Internal RA Finish | 0.51 micron; 20.0787 microinches |
| External RA Finish | 0.76 micron; 29.9213 microinches |
Contact Us for more information on this product and to see other sizes that fit unique applications.
How It Works
The VB16C vacuum breakers are simple and reliable devices that automatically relieve or “break” an unwanted vacuum condition, restoring the atmospheric pressure. This device is particularly suitable for steam heated units of small and medium volume, such as heat exchangers, heating coils, calorifiers, jacketed kettles, steam boilers, etc.
Will be assembled and packaged in a clean room certified according to ISO 14644-1. These products are end capped and sealed with recyclable thermo-shrinkable plastic film, to avoid contamination.
High Purity Ball Valves
High Purity Ball Valves
Specifications
| Model | M3HP True Bore (DN10-50 DIN), M3HP True Bore (1/2”-2” ASME BPE) |
| Service | Clean Steam, gases, and liquids compatible with the construction |
| Sizes | DN 10 to DN 50, ½” to 2” |
| Connections | According to DIN 11850 tube, According to ASME BPE
TC – Sanitary clamps DIN 32676, TC – Sanitary clamps ETO – Extended tube orbital welding TC/ETO – Combination |
| Model | M3HP True Bore (6” ASME BPE) |
| Service | Clean Steam, gases, and liquids compatible with the construction |
| Sizes | 6” |
| Connections | According to ASME BPE
TC – Sanitary clamps ETO – Extended tube orbital welding TC/ETO – Combination |
| Model | M3HP True Bore (2-1/2” – 4” ASME BPE), M3HP Full Bore (DN65-100 DIN) |
| Service | Clean Steam, gases, and liquids compatible with the construction |
| Sizes | 2½” to 4”, DN65 to DN100 |
| Connections | According to ASME BPE, According to DIN 11850 tube
TC – Sanitary clamps , TC – Sanitary clamps DIN 32676 ETO – Extended tube orbital welding TC/ETO – Combination |
Contact Us for more information on this product and to see other sizes that fit unique applications.
Typical Applications
M3HP three-piece body ball valves are isolating valves designed for use with clean steam, condensate and other gases and liquids used in high purity and aseptic processes. The valve is not designed as a control valve and should only be used as an isolating valve, fully open or fully closed. The product is mainly designed for the pharmaceutical, biotech, semiconductor, cosmetics, fine chemical, food and beverage industries.